How To Repair Ionic Air Purifier

Introduction

This guide will show you how to detach your Ionic Cakewalk for repairs or cleaning.

Start by turning off the device, unplugging it and remove the Ionic Breeze "filter". It's more of a tri-blade object rather than a filter but you get the idea.

Start past turning off the device, unplugging it and remove the Ionic Breeze "filter". It's more of a tri-blade object rather than a filter but you go the thought.
Next, lay the device flat and remove the iv screws property the Ionic Breeze to its base and pull it away from the device.

Remove the 2 hidden screws found beneath the base with your #1 screwdriver.

Remove the 2 hidden screws institute beneath the base with your #1 screwdriver.
Remove the 12 smaller screws with your #1 hobby screwdriver.
Yous can only run across 4 of the smaller screws in the photo but I've highlighted their estimated location.
Remove the 4 screws attaching the top of the device to the body with your #1 screwdriver.

Separate the two halves of the body.
Although I have separated the height from the main body in this motion-picture show y'all do not need to worry nigh this at present. Nosotros will practise this in a after stride.
If your goal is to supercede the LEDs so go ahead and divide the elevation electronics from the torso and continue on with the LED Replacement Guide.

Photos depict where to desolder the power cables connexion points. Remove whatever hot glue that may be holding down the cables. These devices are a little seasoned so the glue should not be difficult to remove by hand.
I constitute it easiest to use the base of operations to prop upwardly the trunk, the half of the housing that the electronics typically reside in, in order to get a proficient angle at removing the solder. I'm sure it tin be done on its side but lets work smarter, non harder here.
Think to pull the basis cable completely through the PCB. We will re-thread information technology dorsum through during the reassembly procedure.
Remember, the base is not fastened at this point. Don't knock the Ionic Breeze over while information technology's in an upright position with information technology's internal components exposed.

Gently elevator upward on the tiptop in order to separate it from the half that it is attached to.
Be gentle when lifting the summit equally at that place are cables soldered into place that run down the length of the device. Don't wiggle it out, NO PUN INTENDED, as y'all may impairment these wires or their solder points.
Pull the plastic piece out from its retaining slot.
At this bespeak, the PCB may brand a slight popping sound. It didn't break! It simply popped out of it's retaining slot besides as you lot removed the plastic slice.
Remember, be gentle with the grey plastic piece. It's nonetheless attached to the bottom electronics via the 2 static cords. DO NOT over stretch these cords.
Remove the single screw that's hidden underneath the top/power push unit.

If you lot look at the smaller bottom PCB you lot will discover 2 wires on both sides of it. Slightly above that at that place should exist some hot glue holding these wires to the plastic housing. You cannot come across it in the pic only its estimated location is highlighted in red. Remove this and whatever hot glue that's holding the main power cable in place.
When the glue is removed gently lift the lower plastic piece and the bottom PCB at the aforementioned time. Information technology will come out as ane whole piece.
Place the electronics off to the side.

Yous only demand to exercise this if you lot intend to clean the housing with lather/water. Years of employ volition accept the inside of your Ionic Breeze absolutely filthy, which of class is it's intended purpose. Cleaning information technology won't hurt the housing. I simply scrub past hand with some dish lather to remove the filth. Yous may desire to wear gloves depending on how muddied it is.
Wrap both ends of the power cable existent tight with plastic wrap and wrap the unabridged thing in electrical record.
My photo only depicts wrapping the meridian and lesser only I propose wrapping the whole things in electrical tape if you have enough to spare. Improve safe than distressing.